Step-by-Step Guide to Purchasing MAC Addresses from IEEE for Your Devices

The Ultimate Guide to Acquiring MAC Addresses from IEEE 

FAQ: How to write MAC address into the OTP memory of Raytac’s AN7002Q Wi-Fi module/AN7002Q-DB-5340 DevKit

Recently we have received the FAQ: how to write MAC address into the OTP memory of AN7002Q-P Wi-Fi module? In this article, we’ll get this question explained to give customers a more smooth experience using the AN7002Q-nRF5340 Demo Board(AN7002Q-DB-5340).

Is there an existing Wi-Fi MAC address in the AN7002Q part on the DevKit?

Currently, the AN7002Q module on Raytac’s AN7002Q-DB-5340 board isn’t loaded with a Wi-Fi MAC address.


When running Wi-Fi Scan code/Station code/Shell code…etc. on NCS v2.6.0 (and later versions), the AN7002Q module must have a programed Wi-Fi MAC address to function properly.

Therefore, it’s necessary to follow the below process:
1. Program the original Wi-Fi radio test code (..\nrf\samples\wifi\radio_test) into the MDBT53 section,
2. Then write the Wi-Fi MAC address in to the AN7002Q section via command.

After this, program the original Wi-Fi Scan code/Station code /Shell code … into the 5340, and it will function properly.

*Raytac will assign 2 MAC addresses(for both 2.4GHz & 5GHz) to every AN7002Q module.

*If customers don't have MAC addresses for DevKit development yet, please reach out to service@raytac.com

=========================================================

Case study 1. SCAN code example

Scenario:
Following error occurred when building the SCAN example code, flash it onto the AN7002Q-DB-5340 board, and run the test.

Solution:

When running Wi-Fi scan code on NCS v.2.6.0 or later version, the OTP memory in the AN7002Q module must have a Wi-Fi MAC address programmed in for the Wi-Fi scan functionality to work properly.

(Note: OTP is a One-Time programmable memory, which means the value can only be written once.
The customer must aware of this before performing the OTP operation.)

1. Program the original Wi-Fi radio test code (..\nrf\samples\wifi\radio_test) into the MDBT53 section,
then manually input and execute the following OTP read command.

wifi_radio_ficr_prog otp_read_params

If you see both MAC0 and MAC1 display a value of 0xFF, as shown in above, it means that you haven’t written the Wi-Fi MAC address into the AN7002Q’s OTP.

2. Manually issue the OTP write command to write the Wi-Fi MAC address into the OTP.

https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/wifi/radio_test/ficr.html

wifi_radio_ficr_prog otp_write_params 0x120 0xDDCCBBAA 0xFFEE

wifi_radio_ficr_prog otp_write_params 0x128 0xDDCCBBAA 0xFFEE

After you complete the above, use the OTP read command in below to check if the Wi-Fi MAC address value was written.
The MAC0 and MAC1 should display the value you’ve input from the OTP write command.

wifi_radio_ficr_prog otp_read_params

3. Program the original Wi-Fi SCAN code back into the MDBT53, the Wi-Fi scan functionality should work properly.

==================================================================

Case study 2. Shell code example

SDK Wi-Fi example test – Running Shell Code on AN7002Q-DB-5340:
Scenario:
An error occurs while running Shell code on AN7002Q-DB-5340.

Solution:
The AN7002Q-DB-5340 is paired with nRF5340 DK for development,
but neither of the 2 boards has an external MX25R64 (Serial NOR Flash) component.
So far, only the nRF7002DK board is equipped with the MX25R64.

Therefore, while running the original Wi-Fi shell code, the program will enable SPI NOR.

When using AN7002Q-DB-5340, you should add CONFIG_SPI_NOR=n in the prj.conf file to disable SPI NOR, to turn off any configurations related to it.

After recompiling and flashing, the shell code function
( e.g., Wi-Fi scan/Wi-Fi connect/net ping ..) should work properly.

nRF52840 AT Command USB Dongle MDBT50Q-RX-ATM

To have an easy understanding of Raytac's AT Command USB Dongle, here provides the command table for reader's easy reference.

We encourage readers to visit Raytac's website to obtain the detail information
MDBT50Q-RX-ATM (Click Me)

BT4.0 Mouse/Keyboard Mac 10.9 (Maverick) Compatible

Raytac Corporation
A BT4.0 module maker based on Nordic nRF51 solution (nRF51822 & nRF51422)
www.raytac.com
Tel: +886.2.3234.0208
email: service@raytac.com

BLE (BT4.0) HID device (mostly refer to mouse or keyboard), limited to the usage of Win 8 and Android 4.4 has got a significant improvement recently.

As before, the biggest concerns raised from brands or channel customers to adopt or carry BLE HID products is the market size. ( Win 8 only)

With recent update of Mac 10.9 (Mavericks),  BLE (BT4.0) HID device has turned to be compatible 

to it.

This update may drive the market and consumer buying behaivor has dramatically changing, increasing, and implements of BLE mice or keyboard quickly!